A flush toilet is a toilet A toilet is a plumbing fixture primarily intended for the disposal of human excreta: urine and fecal matter. Additionally, vomit and menstrual waste are sometimes disposed of in toilets in Western societies. The word toilet describes the fixture and, especially in British English, the room containing the fixture. In American English, the latter is that disposes of human waste by using water to flush it through a drainpipe to another location. Flushing mechanisms are found more often on western toilets (used in the sitting position), but many squat toilets A squat toilet is a toilet used by squatting, rather than sitting. There are several types of squat toilets, but they all consist essentially of a hole in the ground. The only exception is a "pedestal" squat toilet, which is the same height as a standard flush toilet. It is also possible to squat over standard western pedestal toilets, also are made for automated flushing. [1] Modern toilets incorporate an 'S','U', 'J', or 'P' shaped bend that causes the water in the toilet bowl to collect and act as a seal against sewer gases. Since flush toilets are typically not designed to handle waste on site, their drain pipes must be connected to waste conveyance and waste treatment The treatment of solid wastes is a key component of waste management. Different forms of solid waste treatment are graded in the waste hierarchy systems.
Contents |
History
Toilet with elevated cistern A cistern is a waterproof receptacle for holding liquids, usually water. Often cisterns are built to catch and store rainwater. Cisterns are distinguished from wells by their waterproof linings. Modern cisterns range in capacity from a few litres to thousands of cubic metres, effectively forming covered reservoirs and chain Categories: Chains | Mechanical power control | Mechanical power transmission attached to lever of discharge valve.As with many inventions, the flush toilet was the result of a long development. Therefore, instead of a single name and date, there follows a list of significant contributions to the history of the device.
- circa 31st century BC: Britain's oldest neolithic village, Skara Brae Skara Brae is a large stone-built Neolithic settlement, located on the Bay of Skaill on the west coast of Mainland, Orkney, Scotland. It consists of ten clustered houses, and was occupied from roughly 3180 BC–2500 BC. It is Europe's most complete Neolithic village and the level of preservation is such that it has gained UNESCO World Heritage, Orkney Orkney also known as the Orkney Islands (and sometimes incorrectly as "The Orkneys"[Notes 1]), is an archipelago in northern Scotland, situated 16 kilometres (10 mi) north of the coast of Caithness. Orkney comprises approximately 70 islands of which 20 are inhabited. The largest island, known as the "Mainland" has an area of 523 utilised a sophisticated water flushing toilet by use of neolithic hydrolic technology.[2] A river and connecting drainage system was incorporated into the village's design to wash waste away.[3]
- circa 26th century BC: Flush toilets were first used in the Indus Valley Civilization The Indus Valley Civilization was a Bronze Age civilization (3300–1300 BCE; mature period 2600–1900 BCE) which was centred mostly in the western part of the Indian Subcontinent and which flourished around the Indus river basin.[n 1] Primarily centered along the Indus and the Punjab region, the civilization extended into the Ghaggar-Hakra River. The cities of Harappa Harappa is an archaeological site in Punjab, northeast Pakistan, about 20 km (12 mi) west of Sahiwal. The site takes its name from a modern village located near the former course of the Ravi River, some 5 km (3 mi) southeast of the site and Mohenjo-daro Mohenjo-daro was one of the largest city-settlements of the Indus Valley Civilization of South Asia situated in the province of Sindh, Pakistan. Built around 2600 BCE, the city was one of the early urban settlements in the world, existing at the same time as the civilizations of ancient Egypt, Mesopotamia, and Crete. The archaeological ruins of had a flush toilet in almost every house, attached to a sophisticated sewage system Sewage collection and disposal systems transport sewage through cities and other inhabited areas to sewage treatment plants to protect public health and prevent disease. Sewage is treated to control water pollution before discharge to surface waters. [4]
- circa 18th century BC: Flush toilet constructed at Knossos Knossos , also known as Labyrinth, or Knossos Palace, is the largest Bronze Age archaeological site on Crete and probably the ceremonial and political centre of the Minoan civilization and culture. The palace appears as a maze of workrooms, living spaces, and store rooms close to a central square. Detailed images of Cretan life in the late Bronze on Minoan The Minoan civilization, a Bronze Age civilization, arose on the island of Crete and flourished from approximately 2700 to 1450 BC. It was rediscovered at the beginning of the 20th century through the work of the British archaeologist Sir Arthur Evans. Will Durant referred to it as "the first link in the European chain." Crete Crete is the largest and most populous of the Greek islands and the fifth largest island in the Mediterranean Sea at 8,336 km2 (3,219 sq mi). Crete is one of the 13 peripheries of Greece and covers the same area as the Greek region of Crete from before the 1987 administrative reform. It forms a significant part of the economy and cultural heritage[5]
- circa 15th century BC: Flush toilets used in the Minoan city of Akrotiri.[citation needed]
- 9th century BC: Flush toilets on Bahrain Bahrain, officially Kingdom of Bahrain , is a small island country in the Persian Gulf ruled by the Al Khalifa royal family. While Bahrain is an archipelago of thirty-three islands, the largest (Bahrain Island) is 55 km (34 mi) long by 18 km (11 mi) wide. Saudi Arabia lies to the west and is connected to Bahrain via the King Fahd Causeway, which Island.[6]
- 1st to 5th centuries AD: Flush toilets were used throughout the Roman Empire The Roman Empire was the post-Republican phase of the ancient Roman civilization, characterised by an autocratic form of government and large territorial holdings in Europe and around the Mediterranean. The term is used to describe the Roman state during and after the time of the first emperor, Augustus. Some examples include those at Vindolanda Vindolanda was a Roman auxiliary fort located at Chesterholm, just south of Hadrian's Wall in northern England, near the modern border with Scotland; it guarded the Stanegate, the Roman road from the River Tyne to the Solway Firth. It is noted for the Vindolanda tablets, among the most important finds of military and private correspondence ( on Hadrian's Wall Hadrian's Wall is a stone and timber fortification built by the Roman Empire across the width of what is now northern England. Begun in AD 122, during the rule of emperor Hadrian, it was the first of two fortifications built across Great Britain, the second being the Antonine Wall in what is now Scotland. Hadrian's Wall is the better known of the in Britain. With the fall of the Roman Empire, the technology was lost in the West.[citation needed]
- 1206: The Arab inventor A number of inventions were developed in the medieval Islamic world, a geopolitical region that has at various times extended from Spain and Africa in the west to the Indian subcontinent and Malay Archipelago in the east. The inventions listed here were developed during the medieval Islamic world, which covers the period from the early Caliphate, Al-Jazari Abū al-'Iz Ibn Ismā'īl ibn al-Razāz al-Jazarī (Arabic: أَبُو اَلْعِزِ بْنُ إسْماعِيلِ بْنُ الرِّزاز الجزري) was a prominent Muslim polymath: a scholar, inventor, mechanical engineer, craftsman, artist, mathematician and astronomer from Al-Jazira, Mesopotamia, who lived during the Islamic Golden, invented a hand washing device incorporating the flush mechanism now used in modern flush toilets. His device features an automaton An automaton is a self-operating machine. The word is sometimes used to describe a robot, more specifically an autonomous robot. An alternative spelling, now obsolete, is automation by a basin filled with water. When the user pulls the lever, the water drains and the automaton refills the basin.[7]
- 1596: Sir John Harington John Harington (August 4, 1561 – November 20, 1612) of Kelston was a courtier, author and master of art. He became a prominent member of Queen Elizabeth I's court, and was known as her 'saucy Godson'. But because of his poetry and other writings, he fell in and out of favour with the Queen, as well as with her successor, James I published A New Discourse of a Stale Subject, Called the Metamorphosis of Ajax, describing a forerunner to the modern flush toilet installed at his house at Kelston[8]. The design had a flush valve to let water out of the tank, and a wash-down design to empty the bowl. He installed one for his godmother Elizabeth I of England Elizabeth I was Queen regnant of England and Queen regnant of Ireland from 17 November 1558 until her death. Sometimes called the Virgin Queen, Gloriana, Oriana, or Good Queen Bess, Elizabeth was the fifth and last monarch of the Tudor dynasty. The daughter of Henry VIII, she was born a princess, but her mother, Anne Boleyn, was executed two and a at Richmond Palace, although she refused to use it because it made too much noise.[citation needed] The Ajax was not taken up on a wide scale in England, but was adopted in France under the name Angrez.
- 1738: A valve-type flush toilet was invented by J. F. Brondel.
- 1775: Alexander Cummings invented the S-trap (British patent no. 814?), still in use today, which uses standing water to seal the outlet of the bowl, preventing the escape of foul air from the sewer. His design had a sliding valve in the bowl outlet above the trap.
- 1777: Samuel Prosser invented and patented the 'plunger closet'.
- 1778: Joseph Bramah Joseph Bramah , born Stainborough Lane Farm, Wentworth, Yorkshire, England, was an inventor and locksmith. He is best known for having invented the hydraulic press. Along with William George Armstrong, he can be considered one of the two fathers of hydraulic engineering invented a hinged valve or 'crank valve' that sealed the bottom of the bowl, and a float valve system for the flush tank. His design was used mainly on boats.
- 1819: Albert Giblin received British patent 4990 for the "Silent Valveless Water Waste Preventer", a siphon discharge system.
- 1852: J. G. Jennings invented a wash-out design with a shallow pan emptying into an S-trap.
- 1857: The first American patent for a toilet, the 'plunger closet', was granted.
- 1858: The first flush toilets on the European continent may have been the three "waterclosets" installed in the new town house of banker Nicolay August Andresen on 6 Kirkegaten in Christiania Oslo (Norwegian pronunciation: [ùʃlu] or [ùslu]) is the capital and largest city in Norway. Founded around 1048 by King Harald III of Norway, the city was largely destroyed by a fire in 1624. The Danish–Norwegian king Christian IV rebuilt the city as Christiania (briefly also spelt Kristiania). In 1925 the city reclaimed its original, insured in January 1859. The toilets were probably imported from England, as they were referred to by the English term "waterclosets" in the insurance ledger.
- 1860: Another early watercloset on the European continent was also imported from England. It was installed in the rooms of Queen Victoria Victoria was the Queen regnant of the United Kingdom of Great Britain and Ireland from 20 June 1837, and the first Empress of India of the British Raj from 1 May 1876, until her death. Her reign as the Queen lasted 63 years and 7 months, longer than that of any other British monarch before or since, and her reign is the longest of any female in castle Ehrenburg (Coburg, Germany); she was the only one who was allowed to use it.
- The first popularized water closets were exhibited at The Crystal Palace The Crystal Palace was a cast-iron and glass building originally erected in Hyde Park, London, England, to house the Great Exhibition of 1851. More than 14,000 exhibitors from around the world gathered in the Palace's 990,000 square feet of exhibition space to display examples of the latest technology developed in the Industrial Revolution and these became the first public toilets. They had attendants dressed in white and customers were charged a penny for use. This is the origin of the phrase "To spend a penny".
- 1880s: Thomas Crapper's plumbing company built flush toilets of Giblin's design. After the company received a royal warrant, Crapper's name became synonymous with flush toilets. Although not the original inventor, Crapper popularized the siphon system for emptying the tank, replacing the earlier floating valve system which was prone to leaks. Some of Crapper's designs were made by Thomas Twyford. The similarity between Crapper's name and the much older word crap is a coincidence.
- 1885: The first modern pedestal 'flush-down' toilet was demonstrated by Frederick Humpherson of the Beaufort Works, Chelsea Chelsea is an area of south-west London, England, bounded to the south by the River Thames, where its frontage runs from Chelsea Bridge along the Chelsea Embankment, Cheyne Walk, Lots Road and Chelsea Harbour. Its eastern boundary was once defined by the River Westbourne, which is now in a pipe above Sloane Square tube station. The modern eastern, England The area now called England has been settled by people of various cultures for about 35,000 years, but it takes its name from the Angles, one of the Germanic tribes who settled during the 5th and 6th centuries. England became a unified state in AD 927, and since the Age of Discovery, which began during the 15th century, has had a significant.[9]
- 1885: Thomas Twyford built the first one-piece ceramic toilet using the flush-out siphon design by J. G. Jennings.
- 1906: William Elvis Sloan invented the Flushometer, which used pressurized water directly from the supply line for faster recycle time between flushes. The Flushometer is still in use today in public restrooms worldwide.
- 1907: Thomas MacAvity Stewart of Saint John, New Brunswick Saint John is the largest city in the province of New Brunswick, and the oldest incorporated city in Canada. The city is situated along the north shore of the Bay of Fundy at the mouth of the Saint John River. In 2006 the city proper had a population of 68,043. The population of the Census Metropolitan Area is 122,389, the second largest in New patented the vortex-flushing toilet bowl, which creates a self cleansing effect.[10]
- 1980: Bruce Thompson, working for Caroma in Australia For at least 40,000 years before European settlement in the late 18th century, Australia was inhabited by indigenous Australians, who belonged to one or more of the roughly 250 language groups. After sporadic visits by fishermen from the immediate north and discovery by Dutch explorers in 1606, Australia's eastern half was claimed by the British, developed the Duoset cistern with two buttons and two flush volumes as a water-saving measure. Modern versions of the Duoset are now available worldwide, and save the average household 67% of their normal water usage.[11]
Flushing mechanisms
The flushing mechanism provides a large flow of water into the bowl (which is described later in this article). The mechanism usually incorporates one or more parts of the following designs:
Tank fill valves
The Ballcock or Float Valve is often used to regulate the filling of a tank or cistern. When the fluid level drops, the float descends, levering the valve opening and allowing more fluid to enter. Once the float reached the 'full' position, the arm presses the valve shut again.Tank fill valves A valve is a device that regulates the flow of a fluid by opening, closing, or partially obstructing various passageways. Valves are technically pipe fittings, but are usually discussed as a separate category. In an open valve, fluid flows in a direction from higher pressure to lower pressure are found in all tank-style toilets. The valves are of two main designs: the side-float design and the concentric-float design. The side-float design has existed for over a hundred years. The concentric-design has only existed since 1957, but is gradually becoming more popular than the side-float design, and Fluidmaster, founded in the United States by inventor Adolf Schoepe, makes them.
The side-float design incorporates a float, usually ball-shaped, which is located to one side of the main valve tower at the end of a rod or arm. As the side-float rises, so does the side-float-arm. The arm is connected to a linkage which blocks the water flow into the toilet tank, and thus maintains a constant level in the tank.
One type of Concentric Float Valve. The Concentric Float valve opens when the fluid level is low, allowing more fluid to enter (Figure 1). When the fluid level returns to the full level, the valve is shut (Figure 2).The newer concentric-float fill valve consists of a tower which is encircled by a plastic float assembly. Operation is otherwise the same as a side-float fill valve, even though the float position is somewhat different. By virtue of its more compact layout, interference between the float and other obstacles (tank insulation, flush valve, and so on) is greatly reduced, thus increasing reliability. The concentric-float fill valve is also designed to signal to users automatically when there is a leak in the tank, by making much more noise when a leak is present than the older style side-float fill valve, which tends to be nearly silent when a slow leak is present.
Tank style with flapper-flush-valve
A traditional gravity toilet tank concluding the flush cycle. As the water level in the tank drops, the flush valve flapper falls back to the bottom, stopping the main flow to the flush tube. Because the tank water level has yet to reach the fill line, water continues to flow from the tank and bowl fill tubes. When the water again reaches the fill line, the float will release the fill valve shaft and water flow will stop. 1. float, 2. fill valve, 3. lift arm, 4. tank fill tube, 5. bowl fill tube, 6. flush valve flapper, 7. overflow tube, 8. flush handle, 9. chain, 10. fill line, 11. fill valve shaft, 12. flush tubeIn a tank-based system, the storage tank (or cistern) collects between 6 and 17 liters of water over a period of time. This system is suitable for locations plumbed with 1/2" (15 mm) or 3/8" (10 mm) water pipes. The storage tank is kept full by a tank fill-valve. The storage tank is usually mounted directly upon the bowl, although some tanks are mounted on the wall above the bowl in an attempt to increase the flush water pressure as it enters the bowl. Tanks near the ceiling are flushed by means of a dangling pull chain, often with a large ornate handle, connected to a flush lever on the cistern itself. "Pulling the chain" remains a British euphemism for flushing the toilet, although this type of tank or cistern is becoming rare. A similar German expression exists: "Wasser ziehen" (to pull water).
In tanks using a flapper-flush-valve, the outlet at the bottom of the tank is covered by a buoyant plastic cover or flapper, which is held in place against a fitting (the flush valve seat) by water pressure. To flush the toilet, the user pushes a lever, which lifts the flush valve from the valve seat. The valve then floats clear of the seat, allowing the tank to empty quickly into the bowl. As the water level drops, the floating flush valve descends back to the bottom of the tank and covers the outlet pipe again. This system is common in homes in the USA ^ b. English is the de facto language of American government and the sole language spoken at home by 80% of Americans age five and older. Spanish is the second most commonly spoken language and in continental Europe. Recently this flush system has also become available in the UK due to a change in regulations.
Tank style with siphon-flush-valve
This system, invented by Albert Giblin and common in the UK The United Kingdom of Great Britain and Northern Ireland[note 7] is a sovereign state located off the northwestern coast of continental Europe. It is an island country, spanning an archipelago including Great Britain, the northeastern part of the island of Ireland, and many small islands. Northern Ireland is the only part of the UK with a land, uses a storage tank similar to that used in the flapper-flush-valve system above. This flush valve system is sometimes referred to as a valveless system, since no traditional type of valve is required. Some would argue, however, that any system of regulating the flow of a fluid is still technically a valve. In the siphon-flush-valve system, the user pushes a lever or button, forcing the water up into the tank siphon passageway which then empties the water in the tank into the bowl. The advantage of a siphon over the flush valve is that is has no sealing washers A washer is a thin plate with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener. Other uses are as a spacer, spring (belleville washer, wave washer), wear pad, preload indicating device, and locking device. Rubber washers may also be used to reduce vibration when fastening fans to computer cases that can wear out and cause leaks, so it is favoured in places where there is a need to conserve water. Until recently, the use of siphon-type cisterns was mandatory in the UK to avoid the potential waste of water by millions of leaking toilets with flapper valves but due to EU harmonisation the regulations have changed. These valves can sometimes be more difficult to operate than a "flapper"-based flush valve because the lever requires more torque than a flapper-flush-valve system. This additional torque required at the tank lever is due to the fact that a user must forcefully lift a certain amount of water up into the siphon passageway in order to initiate the siphon action in the tank.
Older installations, known as "high suite combinations", used a high-level cistern (tank), fitted above head height, that was operated by pulling a chain hanging down from a lever attached to the cistern. When more modern close-coupled cistern and bowl combinations were first introduced, these were first referred to as "low suite combinations". Modern versions have a neater-looking low-level cistern with a lever that the user can reach directly, or a close-coupled cistern that is even lower down and integrated with the bowl. In recent decades the close coupled tank/bowl combination has become the most popular residential system, as it has been found by ceramic engineers that improved waterway design is a more effective way to enhance the bowl's flushing action than high tank mounting.
Tank style with high-pressure or pressure-assist valve
This system utilizes mains water pressure to pre-pressurize a plastic tank located inside of what otherwise appears to be the more typical ceramic flush tank. A flush cycle begins each time a user flushes the bowl. After a user flushes and the water in the pre-pressurized tank has finished emptying into the bowl, the outlet valve in the plastic tank shuts. Then the high pressure water from the city main refills the plastic tank. Inside the tank is an air-filled balloon-like rubber diaphragm. As the higher-pressure mains water enters the tank, the rubber diaphragm is also pressurized and shrinks accordingly. During flushing, the compressed air inside of the diaphragm pushes the water into the bowl at a flow rate which is significantly higher than a tank style gravity-flow toilet. This system requires slightly less water than a gravity-flow toilet. Pressure-assist toilets are sometimes found in both private (single, multiple and lodging) bathrooms as well as light commercial installations (such as offices). They seldom clog, but the pressurized tanks require replacement about once every 10 years. They also tend to be noisier - a concern for residential settings. The inner bowl stays cleaner (in appearance) than gravity counterparts because of the larger water surface area and the toilet's forceful flush. Newer toilets from several companies such as Koehler that are pressure-assisted use 1.4-1.1 gallons per flush
Tankless style with high-pressure (flushometer) valve
In 1906, William Sloan first made his "flushometer" style toilet flush valve, incorporating his patented design[12], available to the public. The design proved to be very popular and efficient, and remains so to this day. Flushometer toilet flush valves are still often installed in commercial restrooms, and are frequently used for both toilets and for urinals. Since they have no tank, they have zero recharge time, and can be used immediately by the next user of the toilet. They can be easily identified by their distinctive chrome pipe-work, and by the absence of a toilet tank or cistern, wherever they are employed.
Some flushometer models require the user to either depress a lever or press a button, which in turn opens a flush valve A valve is a device that regulates the flow of a fluid by opening, closing, or partially obstructing various passageways. Valves are technically pipe fittings, but are usually discussed as a separate category. In an open valve, fluid flows in a direction from higher pressure to lower pressure allowing mains-pressure water to flow directly into the toilet bowl or urinal. Other flushometer models are electronically triggered, using an infrared sensor to initiate the flushing process. Typically, on electronically triggered models, an override button is provided in case the user wishes to manually trigger flushing earlier. Some electronically triggered models also incorporate a true mechanical manual override which can be used in the event of the failure of the electronic system. In retrofit installations, a self-contained battery-powered or hard-wired unit can be added to an existing manual flushometer to flush automatically when a user departs.
Once a flushometer valve has been flushed, and after a preset interval, inside the flushometer valve a pneumatic mechanism closes the valve. The flushometer system requires no storage tank, but requires a high volume of water in a very short time. Thus a 3/4 inch (19 mm) pipe at minimum, or preferably a 1 inch (25 mm) pipe, must be used, but as the high volume is used only for a short duration, very little water is used for the amount of flushing efficacy delivered. Water main pressures must be above 30 psi. While the higher water pressure employed by a flushometer valve does scour the bowl more efficiently than a gravity-driven system, and while fewer blockages typically occur as a result of this higher water pressure, flushometer systems still require approximately the same amount of water as a gravity system to operate (1.6 gpf).
Bowl designs
The bowl, loo or pan, of a toilet is the receptacle that receives bodily waste. A toilet bowl is most often made of porcelain, but can sometimes be made of stainless steel or composite plastics. Toilet bowls are mounted in any one of three basic manners: above-floor mounted (pedestal Pedestal is a term generally applied to the support of a statue or a vase), wall mounted (cantilever A cantilever is a beam supported on only one end. The beam carries the load to the support where it is resisted by moment and shear stress. Cantilever construction allows for overhanging structures without external bracing. Cantilevers can also be constructed with trusses or slabs), or in-floor mounted (natural position A squat toilet is a toilet used by squatting, rather than sitting. There are several types of squat toilets, but they all consist essentially of a hole in the ground. The only exception is a "pedestal" squat toilet, which is the same height as a standard flush toilet. It is also possible to squat over standard western pedestal toilets,).
Within the bowl, there are three main water-way design systems: the siphoning trapped system (found primarily in North American residential installations, and in North American light commercial installations), the non-siphoning trapped system (found in most other installations both inside and outside of North America), and the valve-closet system (found in many specialty applications, such as in trains, planes, buses, and other such installations around the world). Older style toilets called "washout" toilets are now only found in a few locations.
Siphoning-toilets
The siphoning-toilet is perhaps the most popular design in North America for residential and light commercial toilet installations. Some other terms for these types of toilets are "siphon jet", "siphon wash", and in North America, "wash down". All siphoning-toilets incorporate an 'S' shaped water-way. The water-ways in these toilets are designed with slightly smaller diameters than a non-siphoning toilet, so that the water-way will naturally fill up with water, each time it is flushed, thus creating the siphon action. To flush the toilet the user activates a flushing mechanism (see above), which pours a large quantity of water quickly into the bowl. This creates a flow large enough to purge the bowl's water-way of all air, thus causing the bowl to empty rapidly due to the siphonic action that has been created. This flow stops as soon as the water level in the bowl drops below the first bend of the siphon, allowing air to enter the S-pipe to break the column of liquid and to halt the siphonic action.
A "true siphoning-toilet" can be easily identified by the noise it makes. If it can be heard to suck air down the drain at the end of a flush, then it is a true siphoning toilet. If not, then it is a non-siphoning toilet.
Non-siphoning toilets
Three styles of toilet. Figure 1. The Washdown style. Figure 2. The Wash-out style. Figure 3. The Reverse Bowl or Shelf Style. The bowl drain water-way is at the rear of the bowl and is connected to the waste pipe. In American designs the water-way discharge is situated between the rear floor-mount bolts of an extended base. From here it is directly bolted to a drain flange beneath the toilet.Valve closet
The valve closet has a valve or flap at the exit of the bowl with a water-tight seal to retain a pool of water in the pan. When the toilet is flushed, the valve is opened and the water in the pan flows rapidly out of the bowl into the drains, carrying the waste with it.
The earliest type of toilet, the valve closet is now scarce as a water-flush toilet. More complicated in design than other water closets, reliability is lower and maintenance more difficult. The most common use for valve closets is now in portable closets for caravans, camping, trains, and aircraft where the flushing fluid is recycled. This design is also used in train carriages in areas where the waste is allowed to be simply dumped between the tracks (the flushing of such toilets is generally prohibited when the train is in a station).
Washout toilets
Washout toilets have a shallow pool of water into which waste is deposited, with a trapped drain just behind this pool. Waste is cleared out from this pool of water by being swept over into the trap (usually either a P-trap or an S-trap) and then beyond into a sewer by water from the flush. Washout pans were amongst the first types of ceramic toilets invented and since the early 1970s are now only found in a few localities such as in some parts of Germany.
Reverse bowl design
A German style reverse flush toilet which holds the excrement out of the water. This could be to make inspection easier, to reduce splashing, or just tradition. It greatly increases associated odor and may require a brushing after use.In Germany and the Netherlands the bowl is designed to hold the fecal matter out of the water prior to flushing by means of a receiver shelf, whereas most standard designs (U.S., UK) immediately allow it to plunge into standing water. This reverse design prevents the occurrence of any splash-up which commonly happens when fecal matter plunges into the standing water in the standard designs (although substantial deposits may cause splash-up problems of their own). The disadvantage is that it also increases the associated odor and may require the use of a brush after use to clean the shelf. Similar designs are found in some early toilets in the U.S., one particular brand being labeled the "Grand Niagara", as the flushing of the shelf creates a waterfall effect into the drain chamber.
Cultural variations
In India, the "Anglo-Indian" design allows the same toilet to be used in the sitting or the squatting position. This type of toilet is also used on most Russian trains.
For a review of Japanese toilet usage and history, see Toilets in Japan There are two styles of toilets commonly found in Japan. The oldest type is a simple squat toilet, which is still common in public conveniences. After World War II, modern Western-type flush toilets and urinals became common. The current state of the art for Western-style toilets is the bidet toilet, which, as of 2004, are installed in more than.
US standards for low-flow and high-efficiency toilets
A pre 1994 flush-toilet or gravity-fed toilet uses 13 litres (3.4 US gallons or 2.8 imperial gallons) or more per flush. In 1992, the United States Congress The United States Congress is the bicameral legislature of the federal government of the United States of America, consisting of the Senate and the House of Representatives. The Congress meets in the United States Capitol in Washington, D.C passed the Energy Policy Act of 1992 The Energy Policy Act is a United States government act. It was passed by Congress and addressed energy efficiency, energy conservation and energy management (Title I), natural gas imports and exports (Title II), alternative fuels and requiring certain fleets to acquire alternative fuel vehicles, which are capable of operating on nonpetroleum, which mandated that, from 1994, the common flush-toilet use only 1.6 US gallons (6 litres) of water per flush. In response to the Act, manufacturers produced low-flow toilets, which many consumers did not like. Manufacturers responded to consumers' complaints by improving the toilets. The improved products are generally identified as high efficiency toilets or HETs. HETs possess an effective flush volume of 4.8 litres (1.28 US gallons) or less.[13] HETs may be single-flush or dual-flush. A dual-flush toilet permits its user to choose between two amounts of water.[14] Some HETs are pressure-assisted (or power-assisted or pump-assisted or vacuum-assisted). The performance of a flush-toilet may be rated by a Maximum Performance (MaP) score. The low end of MaP scores is 250. The high end of MaP scores is 1000. A toilet with a MaP score of 1000 should provide trouble-free service. It should remove all waste with a single flush; it should not plug; it should not harbor any odor; it should be easy to keep clean. The United States Environmental Protection Agency The U.S. Environmental Protection Agency is an agency of the federal government of the United States charged to protect human health and the environment, by writing and enforcing regulations based on laws passed by Congress. The EPA was proposed by President Richard Nixon and began operation on December 2, 1970, when its establishment was passed uses a MaP score of 350 as the minimum performance threshold for HETs.[13] 1.6 gpf toilets are also sometimes referred as ULF toilets (or Ultra Low Flow) toilets.
Miscellaneous
Toilet trivia
Water-closet (WC), the name
The term "water-closet" was an early term for a room with a toilet. Originally, the term "wash-down closet" was used.[1] Originally, the term "bath-room" referred only to the room where the bathtub was located, which was usually a separate room, but this connotation has changed in common North American usage. In the UK, the terms "bathroom" and "toilet" are used to indicate discrete functions, even though bathrooms in modern homes have been designed according to the American norm since around the mid-sixties. The term "water closet" was probably adapted because in the late 1800s, with the advent of indoor plumbing, a toilet displaced an early clothes closet, closets being shaped to easily accommodate the spatial needs of a commode.[citation needed] The term "water closet" is still used today in some places, but it often refers to a room that has both a toilet and other plumbing fixtures such as a sink or a bathtub. Plumbing manufacturers often use the term "water-closet" to differentiate toilets from urinals A urinal is a specialized toilet for urinating into generally used by males. It has the form of a container or simply a wall, with drainage and automatic or manual flushing. American plumbing codes still refer to a toilet as a "Water Closet" or a "WC". Many South American countries refer to a toilet as a "Water" which is now a term commonly found in Spanish dictionaries, and which derives from the British term "water closet". In French the expression "aller aux waters" ("to go to the waters") has now become obsolete, but it also derives from "water closet". "WC" is still used in the French language, although not as common as the term "toilet", and pronounced as "VC", a shortened version of "double V C". In Germany the expression "Klo" (first syllable of "closet") is still used, though the term is colloquial and not welcome in polite conversation.
In Germany A region named Germania, inhabited by several Germanic peoples, has been known and documented before AD 100. Beginning in the 10th century, German territories formed a central part of the Holy Roman Empire, which lasted until 1806. During the 16th century, northern Germany became the centre of the Protestant Reformation. As a modern nation-state, and the Netherlands The Netherlands (pronounced /ˈnɛðɚləndz/ ; Dutch: Nederland, pronounced [ˈneːdərlɑnt] ( listen)) is a constituent country of the Kingdom of the Netherlands, located in North-West Europe. It is a parliamentary democratic constitutional monarchy. The Netherlands borders the North Sea to the north and west, Belgium to the south, and Germany (due to the bowl design (above)) the toilet is still kept in a separate room known as the "WC" even in newly built residences. In the Dutch Dutch ( Nederlands ) is a West Germanic language spoken by over 22 million people as a native language and over 5 million people as a second language. Most native speakers live in the Netherlands, Belgium, and Suriname, with smaller groups of speakers in parts of France, Germany and several former Dutch colonies. It is closely related to other-speaking part (Flanders Flanders (Dutch: Vlaanderen , French: Flandre, German: Flandern) is the (political) community of the Flemings but also one of the institutions in Belgium, and a geographical region located in parts of present-day Belgium, France, and the Netherlands. Over the course of history, the geographical territory that was called "Flanders" has) as well as the French French is a Romance language spoken as a first language by about 136 million people worldwide. Around 190 million people speak French as a second language, and an additional 200 million speak it as an acquired foreign language. French speaking communities are present in 57 countries and territories. Most native speakers of the language live in-speaking part of Belgium Belgium (pronounced /ˈbɛldʒəm/ , BEL-jəm), officially the Kingdom of Belgium, is a country in northwest Europe. It is a founding member of the European Union and hosts its headquarters, as well as those of other major international organizations, including NATO. Belgium covers an area of 30,528 square kilometres (11,787 sq mi), and it has a (Wallonia), "WC" is a frequently used synonym for "toilet".
Swirl direction
It is a commonly held misconception that when flushed, the water in a toilet bowl swirls one way if the toilet is north of the equator and the other way if south of the equator, due to the Coriolis effect – usually, counter clockwise in the northern hemisphere, and clockwise in the southern hemisphere. In reality, the direction that the water takes is much more determined by the direction that the bowl's rim jets are pointed, and it can be made to flush in either direction in either hemisphere by simply redirecting the rim jets during manufacture. On the scale of bathtubs and toilets, the Coriolis effect is too weak to be observed except under laboratory conditions. [15]
Toilet repairs
Manually filling the bowl
If the flush mechanism should fail in any toilet, the bowl contents can still be flushed out by quickly emptying a large bucket of two or three gallons (ten litres) of water into the bowl all at once. A domestic hose pipe will not work, as it cannot supply water fast enough to fill the siphon tube. (After flushing some water should be added to fill the basin to re-form the gas trap.)
Flush tank repair
For flapper-flush-valve style toilets found mostly in North America, if the handle should have to be held down to achieve a complete flush, an adjustment might need to be made in the handle-float-stopper mechanism. The handle of a toilet is typically attached to a stopper via a chain. A float is attached to the chain between the handle lever and the stopper. The float acts as a counter-balance to allow a certain amount of water to escape through the flush hole in the tank. The float mechanism on the chain should be some distance under the water level of the tank so it can keep the stopper open during a flush until the tank level reaches a certain level. At a certain level the float will pop to the top of the water and the stopper will close. The float should be at a position on the chain where it is under water and does not have so much buoyancy to allow water to leak through the stopper.
For siphon-flush-valve style toilets found mostly in the UK, the siphon's hidden, oblong, plastic diaphragm will tend to split and crack after approximately 10 years. The effectiveness of the flush can deteriorate suddenly or gradually as the cracking increases. This will often prompt owners to replace much of the system. However, the diaphragms are of a standard design and are inexpensive (50p) and simple to replace. Inside the cistern, unhooking the flush-handle's s-link allows the plunger and diaphragm to be removed, once the lower part of the siphon is unscrewed (it is not necessary to remove the whole assembly with some multiple part siphons—the main outlet pipe can be left in place. Most are one piece and require removing from the cistern completely. There is also a small rubber diaphragm in the ballcock inlet assembly, which can deteriorate over a period of around 10 years—if adjusting the water level becomes problematic, it is worth changing this inexpensive diaphragm.
See also
- Pail closet
- Ecological sanitation
- Low flush toilet
- Plumbing
- Plumbing fixtures
- Squat toilet
- Toilet
- Toilet rim block
- Toilets in Japan
- Urinal
- Washroom
References
- ^ "Flushing squat toilets", naturesplatform.com
- ^ Clean: a history of personal hygiene and purity By Virginia Sarah Smith
- ^ The ancient world By John Dougan
- ^ Rodda, J. C. and Ubertini, Lucio (2004). The Basis of Civilization - Water Science? pg 161. International Association of Hydrological Sciences (International Association of Hydrological Sciences Press 2004).
- ^ C. Michael Hogan. 2007. Knossos fieldnotes, The Modern Antiquarian
- ^ Sulabh International Museum of Toilets
- ^ Rosheim, Mark E. (1994), Robot Evolution: The Development of Anthrobotics, Wiley-IEEE, pp. 9–10, ISBN 0471026220
- ^ Kinghorn, Jonathan (1986), "A Privvie in Perfection: Sir John Harrington's Water Closet", Bath History 1: 173–188. ISBN 086299294X. Kinghorn supervised a modern reconstruction in 1981, based on the illustrated description by Harington's assistant Thomas Coombe in the New Discourse.
- ^ Eveleigh, David J. (2008). Privies and Water Closets. Oxford: Shire Publiations. ISBN 978-0-7478-0702-5.
- ^ Mario Theriault, Great Maritime Inventions 1833-1950, Goose Lane Editions, 2001, p. 34.
- ^ 100 Years of Australian Innovation - Dual flush technology
- ^ Sloan, William, "Valve", US patent 977562, issued December 6, 1910
- ^ a b Testing of Popular Toilet Models by Veritec Consulting
- ^ "Low-flow revolution: As water concerns rise, toilet makers meeting the challenge", Lacrosse Tribune, 26 November 2007; accessed 3 January 2009
- ^ "Do bathtubs drain counterclockwise in the Northern Hemisphere?", The Straight Dope, April 15, 1983]
External links
| Wikimedia Commons has media related to: Toilet flush |
- Intelligent Bathroom Fixtures and Systems (comparison between passive and active vision systems for use with plumbing fixtures, as published in Leonardo, 36(3), pp 199–120, June 2003)
- A Brief history of Wells and Toilets, 2005 book (link to pdf-file)
- Did Thomas Crapper invent the flush toilet? - at Snopes
- "Superflushing their way to the Super Bowl" - PM Engineer
|
|||||||||||||||||||||||
Categories: Toilet types | British inventions
|
Vernon Morning Star
A low flush toilet uses six litres of water per flush compared to 13 litres used by older models. Just think how much water we would save in one year if ...
Christopher Pollon
Wed, 14 Jul 2010 14:02:00 GM
Perhaps the biggest challenge here -- and anywhere else wanting to harvest rainwater -- is that it is currently illegal to use rainwater to . flush toilets. in the City of Vancouver. The design team had to earn "equivalencies" from the ...
Q. must flush toilet a couple of times before it clears. after bath the toilet bubbles up.
Asked by Alice G - Mon Apr 9 23:59:10 2007 - - 7 Answers - 0 Comments
A. Your main line has a blockage. Call someone out to clean the lines. What happens, is the pipes fill up with water, and then slowly drain. More than likely roots got in the pipe where it comes out from under the house.
Answered by edjumacation - Tue Apr 10 00:12:15 2007
